System Log Information

Access to NetWare server <file server name> denied. Either there is no account for this print server on the NetWare server or the password was incorrect.

(In the print server mode) Login to the file server failed. Make sure that the print server is registered on the file server. If a password is specified for the print server, delete it.

account is unavailable: Same account name be used.

User account is disabled. This could be because it use the same account name as the administrator account.

account is unavailable: The authentication password is not set up.

User account is disabled. This could be because the authentication password is not set, and only the encryption account is set.

account is unavailable: encryption is impossible.

Encryption is not possible and account is disabled. This could be because:

• Security option is not installed.

• Encryption password has not been specified.

add_sess_IPv4: bad trap<IPv4 address>, community:<community name>

The IPv4 address (0.0.0.0.) is unavailable when the community access type is TRAP. Specify the host IPv4 address for the TRAP destination.

add_sess_IPv6: bad trap<IPv6 address>, community:<community name>

The IPv6 address [::] is unavailable when the community access type is TRAP. Specify the host IPv6 address for the TRAP destination.

add_sess_IPv4: community<community name> already defined.

The same community name already exists. Use another community name.

add_sess_IPv6: community <community name> already defined.

The same community name already exists. Use another community name.

add_sess_IPX: bad trap<IPX address>community <community name>

The IPX address (00:00:00:00:00:00) is unavailable when the community access type is TRAP. Specify the host IPX address for the TRAP destination.

add_sess_IPX: community <communityname> already defined.

The same community name already exists. Use another community name.

Attach FileServer= <file servername>

Connection to the file server as the nearest server has been established.

Attach to print queue <print queue name>

(In the print server mode) Attached to the print queue.

Authentication mode mismatch< SSID >

Authentication mode is different to the AP. The required SSID is the SSID of the access point connected to when in infrastructure mode.

centrod is disabled.

Communication via parallel connections unavailable because centrod is disabled in the security mode.

Enable centrod in the security mode.

Cannot create service connection

(In the remote printer mode) Connection to the file server has not been established. The number of file server users may have exceeded the maximum capacity of the file server.

Cannot find rprinter (<print server name>/<printer number>)

The printer with the number displayed on the print server does not exist. Make sure that the printer number is registered on the print server.

Change IP address from DHCP Server.

The IP address changes when DHCP lease is renewed. To always assign the same IP address, set a static IP address to the DHCP server.

child process exec error! (process name)

The network service failed to start. Turn the printer off and then on. If this does not work, contact your service or sales representative.

Client password rejected

The client's password was rejected. Check the client password.

Client tls certificate rejected

The client's TLS certificate was rejected. Check the certificate.

Connected DHCP Server(<DHCP serveraddress>).

The IP address was successfully received from the DHCP server.

Could not attach to FileServer<error number>

(In the remote printer mode) Connection to the file server has not been established. The file server has refused the connection. Check the file server configuration.

Could not attach to PServer<print server>

(In the remote printermode) Connection to the print server has not been established. The print server has refused the connection. Check the print server configuration.

Current Interface Speed: xxxMbps

Speed of the network (10Mbps, 100 Mbps, or 1Gbps).

Current IP address <currentIP address>

Current IPv4 address.

Current IPX address<IPX address>

Current IPX address

DHCP lease time expired.

DHCP lease time has expired. The printer tries to discover the DHCP server again. The IP address until now becomes invalid.

DHCP server not found.

The DHCP server was not found. Make sure that the DHCP is on the network.

dhcpcd start.

The DHCPCD service (dhcp client service) has started.

Duplicate IP=<IP address>(from<MAC address>).

The same IP address (IPv4, or IPv6 address) was used. Each IP address (IPv4, or IPv6 address) must be unique. Check the address of the device indicated in [MAC address].

Established SPX Connection with PServer, (RPSocket=<socketnumber>, connID=<connection ID>)

(In the remote printer mode) Connection to the print server has been established.

exiting

The lpd service has ended and the system is exiting the process.

Exit pserver

(In the print server mode) The print server function is disabled because the necessary print server settings have not been made.

Frametype =<frame typename>

The frame type name is configured to be used on NetWare.

httpd start.

The httpd service has started.

IEEE 802.11b <communication mode> mode

Displays wireless LAN communication mode.

inetd start.

The inetd service has started.

Interface (interface name): Duplicate IP Address (IP address).

The same IP (IPv4 or IPv6) address was used. Each IP address must be unique. Check the address of the device indicated in [IP address].

< Interface > started with IP: < IP address >

IP address (IPv4, or IPv4 address) has been set for the interface and is operating.

< Interface >: Subnet overlap.

The same IP address (IPv4, or IPv6 address) and the subnet mask is used with other device.

IPP cancel-job: permission denied.

The printer could not authenticate the name of the user attempting to cancel a job.

IPP job canceled. jobid=%d.

The spooled job was canceled due to error or user request.

LeaseTime=<lease time>(sec), RenewTime=<renewtime>(sec).

The resource lease time received from the DHCP server is displayed in [lease time] in seconds. The renewal time is displayed in [renew time] in seconds.

Login to fileserver <file server name> (<IPX|IPv4|IPv6>,<NDS|BINDERY>)

(In the print server mode) Login to the file server is in the NDS or BINDERY mode.

Memory allocate error.

Data cannot be obtained.

Disconnect the USB cable, and then connect it.

Name registration success. WINS Server=<WINS server address> NetBIOS Name=<NetBIOS name>

Name registration of <NetBIOS Name> to <WINS server address> was successful.

Name registration success in Broadcast name=<NetBIOS Name>

Name registration by Broadcast name of <NetBIOS Name> was successful.

Name registration failed. name=<NetBIOS name>

Name registration of <NetBIOSName> failed. Change to different NetBIOS name.

nbtd start.

The nbtd service has started.

nprinter start (Netware)

(In the remote printer mode) The NetWare service has started.

nwstart start. (NetWare)

The service for NetWare protocol stack setting has started.

Open log file <file name>

(In the print server mode) The specified log file has been opened.

phy release file open failed.

Replacing the network interface board is required. Contact your sales or service representative.

Print queue <print queue name> cannot be serviced by printer 0, <print server name>

(In the print server mode) The print queue cannot be established. Make sure that print queue exists on the specified file server.

Print server <print servername>has no printer.

(In the print server mode) The printer is not assigned to the print server. Using NWadmin, assign the printer, and then restart it.

print session full

No more print jobs can be accepted.

Printer <printer name> has no queue

(In the print server mode) The print queue is not assigned to the printer. Using NWadmin, assign the print queue to the printer, and then restart it.

pserver start. (NetWare)

(In the print server mode) The NetWare service has started.

Required file server (<file servername>) not found

The required file server is not found.

received EAP Failure

EAP reception failed.

restarted.

The lpd service has started.

sap enable, saptype=<SAP type>, sapname=<SAP name>

The SAP function has started. The SAP packet is issued to advertise the service on the SAP table on the NetWare server.

server identity invalid

The server ID is disabled. Check the server authentication.

session IPv4 <community name> not defined.

The requested community name is not defined.

session IPv6 <community name> not defined.

The requested community name is not defined.

session <community name> already defined.

The requested community name is not defined.

session_ipx <community name> not defined.

The requested community name is not defined.

Set context to <NDS contextname>

An NDS context name has been set.

smbd start. (NETBIOS)

The smbd service has started.

SMTPC: failed to get smtp server ip-address.

The SMTP server IP address could not be obtained. This could be because:

• The specified DNS server could not be found.

• No connection to the network has been established.

• The specified DNS server could not be found.

• An incorrect DNS server is specified.

• The specified SMTP server IP address could not be found in the DNS server.

SMTPC: failed to connect smtp server. timeout.

Connection to the SMTP server failed due to timeout. This could be because the specified SMTP server name is incorrect, or no connection to the network has been established, or the network configuration is incorrect, so there is no response from the SMTP server. Check the SMTP server name, or the network connection and configuration.

SMTPC: refused connect by smtp server.

Connection to the SMTP server is denied. This could be because server other than the SMTP server has been specified, or the specified SMTP server port number is incorrect. Check the SMTP server name, port number, or the SMTP server port number.

SMTPC: no smtp server. connection close.

Connection to the SMTP server failed due to no response from SMTP. This could be because a server other than the SMTP server has been specified, or the specified SMTP server port number is incorrect. Check the SMTP server name, port number, or the SMTP server port number.

SMTPC: failed to connect smtp server.

Connection to the SMTP server failed. This could be because no connection to the network has been established, or the network configuration is incorrect, so there is no response from the SMTP server, or the specified SMTP server name is incorrect, or the specified SMTP server IP address could not be found in the DNS server, or a server other than the SMTP server has been specified, or the specified SMTP server port number is incorrect. Check the DNS Server's IP address and SMTP server's IP address, or the SMTP server name and SMTP port number, or the SMTP server's SMTP port number, or the network connection and configuration.

SMTPC: username or password wasn't correct. [response code] (information)

Connection to the SMTP server failed, because the specified SMTP user name is incorrect, or the specified SMTP password is incorrect. Check the SMTP user name and password.

Snmp over IPv4 is ready

Communication over IPv4 with snmp is available.

Snmp over IPv6 is ready.

Communication over IPv6 with snmp is available.

Snmp over IPX is ready.

Communication over IPX with snmp is available.

snmpd start.

The snmpd service has started.

started.

The direct print service has started.

Started.

The bonjour (rendezvous) function is enabled.

Terminated.

The bonjour (rendezvous) function is disabled.

The print server received error <error number> during attempt to log in to the network. Access to the network was denied. Verify that the print server name and password are correct.

Login to the file server failed. The print server is not registered or a password is specified. Register the print server without specifying a password.

trap account is unavailable.

v3Trap cannot be sent. This could be because the Trap destination account is different from the account specified by the printer.

usbd is disable.

Plug and Play function and printing is disabled because usbd is disabled in the security mode.

Enable usbd in the security mode.

WINS name registration: No response to server<WINS server address>

There was no response from the WINS server. Check the correct WINS server address is entered. Alternatively, check the WINS server is functioning properly.

WINS wrong scopeID=<Scope ID>

An invalid scope ID was used. Use a valid scope ID.

wpa authentication Failed

WPA authentication failed. Check the WPA configuration.

wpa authentication started

WPA authentication has started.

wpa IEEE802.1X started

WPA authentication has started.

wpa connecting to authenticator

WPA is connecting to authenticator.

wpa link up

WPA key exchange has finished, and communication has been terminated.

wpa probe response doesn't have IE.

WPA probe response does not have IE.

wpa success authenticated

WPA authentication was successful.

wpa success key received

WPA key reception was successful.

wpa waiting for key

Waiting for WPA key.

wpasupd start

wpasupd has started.

wpasupd stop

wpasupd has ended.