Current Printer Status

• UNIX: Use the "lpq" command and "rsh", "rcp", "ftp" and "sftp" parameters.

• mshell: Use the "status" command.

  Messages	Description
  Call Service Center	There is a malfunction in the printer.
  Canceling Job...	The job is being reset.
  Configuring...	Setting is being changed.
  Cover Open: Bridge Unit Left	The left cover of the Bridge Unit is open.
  Cover Open: Bridge Unit Right	The right cover of the Bridge Unit is open.
  Cover Open: Duplex Unit	The cover of the duplex unit is open.
  Cover Open: Finisher	The cover of Finisher is open.
  Cover Open: Finisher Front	The front cover of Finisher is open.
  Cover Open: Finisher Upper	The upper cover of Finisher is open.
  Cover Open: Front Cover	The front cover is open.
  Cover Open: LCT	The LCT cover is open.
  Cover Open: Lower Right Cover	The lower right cover is open.
  Cover Open: Upper Right Cover	The upper right cover of the duplex unit is open.
  Current Job Suspended	Current job is suspended.
  Empty: Black Toner	The black toner cartridge is almost empty.
  Energy Saver Mode	The printer is in Energy Saver Mode.
  Error: Ethernet Board	An Ethernet board error has occurred.
  Error: HDD Board	A hard disk drive board error has occurred.
  Error: Optional Font	An error has occurred in the font file of the printer.
  Error: Optional RAM	An error has occurred in the optional memory unit.
  Error: Parallel I/F Board	An error has occurred in the parallel interface.
  Error: PDL	An error has occurred in the page description language.
  Error: Rem. Certificate Renewal	An error has occurred in the remote certificate renewal.
  Error: USB Interface	An error has occurred in the USB interface.
  Error: Wireless Board	An error has occurred in the wireless board.
  Error: Wireless Card	Wireless card is not inserted during start up, or the wireless LAN interface unit or the wireless card is taken out after start up.
  Full: Finisher	Finisher tray is full.
  Full: Finisher Shift Tray	Shift tray of Finisher is full.
  Full: Finisher Upper Tray	The upper tray of Finisher is full.
  Full: Hole Punch Receptacle	Punch Chip receptacle for hole punch is full.
  Full: Log Data Capacity	Log data capacity is full.
  Full: Standard Tray	Standard output tray is full.
  Full: Waste Toner	Waste toner is full.
  Hex Dump Mode	It is a hex dump mode.
  Jobs Suspended	All jobs are suspended.
  Log Data Transfer failed	Log transfer has failed.
  Low: Toner	The black toner cartridge is not set correctly, or toner is almost running out.
  Malfunction: Finisher	There is a problem with Finisher.
  Malfunction: Staple Unit	There is a problem with the staple unit.
  Malfunction: Tray 1	There is a problem with tray 1.
  Malfunction: Tray 2	There is a problem with tray 2.
  Malfunction: Tray 3	There is a problem with tray 3.
  Malfunction: Tray 4	There is a problem with tray 4.
  Malfunction: LCT	There is a problem with the large capacity tray.
  Mismatch: Paper Size	Indicated paper tray does not contain paper of selected size.
  Mismatch: Paper Size and Type	Indicated paper tray does not contain paper of selected size and type.
  Mismatch: Paper Type	Indicated paper tray does not contain paper of selected type.
  Near Replacing: MaintenanceKitA	Prepare new Maintenance Kit A.
  Near Replacing: MaintenanceKitB	Prepare new Maintenance Kit B.
  Nearly Full: Log Data Capacity	Log data capacity is nearly full.
  Nearly Full: Waste Toner	Waste toner bottle is nearly full.
  Need more Staples	Stapler has almost run out of staples.
  No Paper: LCT	There is no paper in Large Capacity tray.
  No Paper: Selected Tray	There is no paper in specified tray.
  No Paper: Tray 1	There is no paper in tray 1.
  No Paper: Tray 2	There is no paper in tray 2.
  No Paper: Tray 3	There is no paper in tray 3.
  No Paper: Tray 4	There is no paper in tray 4.
  Not Detected: Develop. Unit (K)	The development unit (black) is not correctly set.
  Not Detected: Duplex Unit	The duplex unit is not correctly set.
  Not Detected: Fusing Unit	The fusing unit is not correctly set.
  Not Detected: Input Tray	The paper feed tray is not correctly set.
  Not Detected: Transfer Unit	The transfer unit is not correctly set.
  Not Detected: Tray 1	Tray 1 is not correctly set.
  Not Detected: Tray 2	Tray 2 is not correctly set.
  Not Detected: Tray 3	Tray 3 is not correctly set.
  Not Detected: Tray 4	Tray 3 is not correctly set. (LCT)
  Not Detected: LCT	Tray 4 is not correctly set.
  Offline	Printer is offline.
  Paper in Duplex Unit	The paper remains in the duplex unit.
  Paper in Finisher	The paper remains in Finisher.
  Paper Misfeed: Duplex Unit	The paper has jammed in the duplex unit.
  Paper Misfeed: Finisher	The paper has jammed in the finisher.
  Paper Misfeed: Input Tray	The paper has jammed in the input tray.
  Paper Misfeed: Internal/Output	The paper has jammed inside the printer.
  Printing...	Printing is in progress.
  Proxy Address/Port Incorrect	Proxy address or Port No. is incorrect.
  Proxy User/Password Incorrect	Proxy user name or Password is incorrect.
  Ready	The printer is ready to print.
  Renewing Remote Certificate	Remote Certificate is Renewing.
  Replace Maintenance Kit A	It is time to replace Maintenance Kit A.
  Replace Maintenance Kit B	It is time to replace Maintenance Kit B.
  Reset IPDS fonts	The IPDS fonts are being reset.
  SD Card Authentication failed	SD card authentication failed.
  Supplies Order Call failed	The supply order call has failed.
  Tray Error: Duplex Printing	Selected paper tray cannot be used for duplex printing.
  Warming Up...	The printer is warming up.